Premium custom o ring supplier? DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad. See additional details on custom o ring manufacturer.
The spring seal produced by DMS SEALS is perfect for being applied to extremely high-speed, very low-speed equipment with micro piston strokes and other special operating conditions. It can be used with rotary seals and maintains good sealing performance in violent shake and vibration motion environments. At the same time, our seals are extremely adaptable to a wide range of working media. It is resistant to a wide range of chemicals except for soluble alkali metals, high-temperature fluorine and chlorine trifluoride. Therefore, it works well with liquids such as oils and water with high and low temperature.
DMS SEALS’ s bonded seal is ideal for being applied to threaded pipe fittings and plug sealing in Metric, British and BSP systems. The seal has no special requirements for the positioning and processing techniques of the seal groove, so it is an ideal accessory for fast and automatic installation that we highly recommend. The operating temperature range is -30°C ~ 100°C, and the working pressure is less than 39.2 MPa. It is commonly used in a hydraulic oil medium.
DMS Seals piston seals can be used very effectively in the clearance between the two chambers of the hydraulic cylinder and cylinder. The piston seal is pushed by the pressure of the fluid. Its good working performance can improve the efficiency of the machine. Due to its excellent resistance to leakage, it helps the machine to extend the machine’s working life. Our seals provide the best tight adhesion for the sealing system with low internal leakage and frictional resistance.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
However, hydraulic transmission also has disadvantages compared with mechanical transmission: It is easy to leak and not friendly to the environment. High manufacturing precision is required. Low efficiency. The transmission ratio is not fixed. Due to the special working environment of construction machinery, its hydraulic system has the following characteristics: The working hours are irregular, and sometimes work continuously for a long time. The working environment is outdoors, the working temperature difference is large, and the working environment is dusty. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small. Due to the volume and weight, the working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa.
Supplied in rolls or open loops. The open ring can be directly installed and used, but it must be cut when the roll is used, and the cutting length must be calculated in advance: there can only be one opening, the opening form is an oblique 45° opening, and the opening distance is about 3-15mm, or the diameter of the guide ring 3-5% of . Under normal circumstances, the openings are oblique openings. Straight openings or zigzag openings are rare and have specific uses and purposes. There are two purposes for the opening. The first is to facilitate installation. If it is not opened, it is an integral ring, which is difficult to install or impossible to install, so it must be opened. Secondly, the opening and a certain opening distance are reserved to facilitate the automatic coordination of volume changes. Otherwise, the movement may be stuck or the moving parts may be pulled due to the excessive expansion of the guide belt under certain conditions. Coiled ones are relatively cheap, and the same coil can be used to make guide rings of different sizes. Read additional details on https://www.dmsseals.com/.