High quality hydraulic seal factory: Basics of fluid pump sealing – A mechanical seal is simply a method of containing fluid within a vessel (typically pumps, mixers, etc.) where a rotating shaft passes through a stationary housing or occasionally, where the housing rotates around the shaft. When sealing a centrifugal pump, the challenge is to allow a rotating shaft to enter the ‘wet’ area of the pump, without allowing large volumes of pressurized fluid to escape. To address this challenge there needs to be a seal between the shaft and the pump housing that can contain the pressure of the process being pumped and withstand the friction caused by the shaft rotating. The gap between the faces on a typical seal is as little as 1 micron – 75 times narrower than a human hair. Because the gap is so tiny, particles that would otherwise damage the seal faces are unable to enter, and the amount of liquid that leaks through this space is so small that it appears as vapor – around ½ a teaspoon a day on a typical application. Discover more info at wiper seals.
Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications.
Construction machinery sealing system requirements: High and low temperature resistance Because of continuous work for a long time, if it is outdoors in summer, the hydraulic oil temperature of the machine may exceed 100°C, which requires the seal to be resistant to high temperature. If it is outdoors in winter, the temperature may be around -40°C when it is just turned on, and the seals are required to be resistant to low temperatures. Therefore, the sealing system is required to withstand a wide temperature range. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small.
The radial force of our rotary seals on the shaft and the distribution is very reasonable. It can achieve the optimal “critical oil film thickness” working condition and always maintain critical lubrication. We guarantee that our rotary seal can help the machine get the sharpest “peak” pressure distribution with the least radial force, providing the best sealing effect. The bearing seal is designed by DMS SEALS to isolate the moving metal part, guiding the piston and piston rod of the hydraulic cylinder to move in a certain direction and it can help withstand lateral loads. It helps prevent any direct contact between the piston metal and the cylinder metal and prevents strain and seal damage on the inner surface of the cylinder.
Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.
Our piston seals are designed to provide excellent leak control. We guarantee that it can perfectly meet the user’s requirements for low friction, compactness, precise configuration and simple installation. It is designed for fluid power applications. It is made of compound materials with high performance, which guarantees excellent wear resistance and excellent extrusion resistance for the seal. It is designed to be suitable for almost all fluid media and is highly resistant to oxidation and corrosion. It has excellent dynamic and static sealing performance and can even work under dusty industrial environments. Moreover, it has strong adaptability to various working conditions and can adapt to a fast, high-pressure working environment. At the same time, it has unparalleled performance in extreme temperature environments.
Destroy the leak: The working conditions of the sealing part are relatively bad, the thermal deformation is large, it is often subjected to vibration, impact, improper installation, excessive tightening force, repeated use, compression deformation, internal stress concentration, damage beyond the fatigue strength, material aging, deterioration, etc. will cause damage to leaks. This kind of leakage has the greatest impact and great harm, so it is necessary to strengthen prevention.
Supplied in rolls or open loops. The open ring can be directly installed and used, but it must be cut when the roll is used, and the cutting length must be calculated in advance: there can only be one opening, the opening form is an oblique 45° opening, and the opening distance is about 3-15mm, or the diameter of the guide ring 3-5% of . Under normal circumstances, the openings are oblique openings. Straight openings or zigzag openings are rare and have specific uses and purposes. There are two purposes for the opening. The first is to facilitate installation. If it is not opened, it is an integral ring, which is difficult to install or impossible to install, so it must be opened. Secondly, the opening and a certain opening distance are reserved to facilitate the automatic coordination of volume changes. Otherwise, the movement may be stuck or the moving parts may be pulled due to the excessive expansion of the guide belt under certain conditions. Coiled ones are relatively cheap, and the same coil can be used to make guide rings of different sizes. Find extra info at https://www.dmsseals.com/.
DMS Seals is a professional hydraulic seals, industrial mechanical seals manufacturer and oil seal supplier specializing in supplying sealing solutions and various seals & o ring. As a leading custom o ring manufacturer, DMS can support OEM and ODM and can meet customers’ requests. DMS Seals adheres to the tenet of “first-class design, top manufacturing, excellent service” and strive to be an excellent supplier of sealing system solutions. DMS Seals pays the utmost attention to quality to ensure the satisfaction of our cooperative partners.